SOLVED: The JammASD board does not take button 6, 7 & 8 inputs from the Jamma harness. They have to be wired seperately.
I snipped the button 6 wires that led from the buttons to the Jamma harness and wired them directly into the JammASD board.
Search found 12 matches
- Mon Aug 29, 2022 2:18 pm
- Forum: Hardware Setups
- Topic: MiSTer with JammASD Button 6 not Responding [Solved]
- Replies: 4
- Views: 1075
- Fri Aug 26, 2022 5:24 pm
- Forum: Hardware Setups
- Topic: MiSTer with JammASD Button 6 not Responding [Solved]
- Replies: 4
- Views: 1075
MiSTer with JammASD Button 6 not Responding [Solved]
I've got my MiSTer setup with a JammASD which is connected to my Jamma harness. The same Jamma harness, when connected to my Jamma board (412 vertical games) works perfectly and all buttons respond in the input test. However when connected to my MiSTer I can't get button 6 to respond at all. Couple of questions: Are there any troubleshooting steps ...
- Mon Jun 13, 2022 1:16 pm
- Forum: General Discussions
- Topic: New Build Cannot Find Cores
- Replies: 7
- Views: 976
- Mon Jun 13, 2022 9:11 am
- Forum: Official Addon Boards
- Topic: Flashing Red / Amber LED's After Installing IO Board v6.1
- Replies: 9
- Views: 10495
Re: Flashing Red / Amber LED's After Installing IO Board v6.1
Perfect thanks! I must admit I was nervous about blowing up my DE10FPGA64 wrote: ↑Sun Jun 12, 2022 4:15 pm I would get the one from MisterFpga.co.uk
https://misterfpga.co.uk/product/mister ... er-supply/
much better power supply. Although do remember you need the mains to the power pack cable too
- Mon Jun 13, 2022 9:07 am
- Forum: General Discussions
- Topic: New Build Cannot Find Cores
- Replies: 7
- Views: 976
Re: New Build Cannot Find Cores
Ah yes. I've made this change and started the script again. It's currently pulling down the additional files so fingers crossed. I'll report back.
- Mon Jun 13, 2022 6:53 am
- Forum: General Discussions
- Topic: New Build Cannot Find Cores
- Replies: 7
- Views: 976
Re: New Build Cannot Find Cores
Hmm there is no “_Arcade/MAME” directory even when i rebuild. Can anyone else verify this?
- Sun Jun 12, 2022 6:36 pm
- Forum: General Discussions
- Topic: New Build Cannot Find Cores
- Replies: 7
- Views: 976
Re: New Build Cannot Find Cores
Thanks @MorkMikael
The “_Arcade” directory contains all the games you’d expect to see including Silkworm. I don’t see a MAME directory but is that a requirement?
I have run the update_all script multiple times with no difference.
The “_Arcade” directory contains all the games you’d expect to see including Silkworm. I don’t see a MAME directory but is that a requirement?
I have run the update_all script multiple times with no difference.
- Sun Jun 12, 2022 2:48 pm
- Forum: General Discussions
- Topic: New Build Cannot Find Cores
- Replies: 7
- Views: 976
New Build Cannot Find Cores
Just reformatted and rebuilt my MicroSD card using Mr Fusion and the Update All script. Upon completion if I try to launch any cores I get an error as per the below example (where I launched the Arcade Silkworm core): /media/fat/_Arcade/mame/silkwor silkworm.1 not found When I check the MicroSD card there is no MAME directory and I'm not sure why i...
- Sun Jun 12, 2022 2:36 pm
- Forum: Official Addon Boards
- Topic: Flashing Red / Amber LED's After Installing IO Board v6.1
- Replies: 9
- Views: 10495
Re: Flashing Red / Amber LED's After Installing IO Board v6.1
It's power supply related.
I was using a USB cable connected to the mains with an Apple 5W USB plug. This just gives me the flashing red/amber LED's.
If I use the exact same setup with the USB connected to a USB 3 port on my laptop then it works fine.
I need to purchase a proper power supply.
- Sat Jun 11, 2022 12:40 pm
- Forum: Official Addon Boards
- Topic: Flashing Red / Amber LED's After Installing IO Board v6.1
- Replies: 9
- Views: 10495
Re: Flashing Red / Amber LED's After Installing IO Board v6.1
UPDATE 2: I removed the SDRAM module and rebooted and I'm now seeing the "Mr Fusion is installing MiSTer" screen. Stay tuned.
- Fri Jun 10, 2022 5:33 pm
- Forum: Official Addon Boards
- Topic: Flashing Red / Amber LED's After Installing IO Board v6.1
- Replies: 9
- Views: 10495
Re: Flashing Red / Amber LED's After Installing IO Board v6.1
UPDATE: I've removed the IO board and wiped the MicroSD card. Reinstalled Mr Fusion and booted up but getting nothing from the display through HDMI at all. Tried a second MicroSD card with Mr Fusion and it's the same. No display.
Is there a way to flush/reset the DE10?
Is there a way to flush/reset the DE10?
- Fri Jun 10, 2022 4:05 pm
- Forum: Official Addon Boards
- Topic: Flashing Red / Amber LED's After Installing IO Board v6.1
- Replies: 9
- Views: 10495
Flashing Red / Amber LED's After Installing IO Board v6.1
My DE10 worked perfectly until I installed my IO Board. Now when I power-up I just get alternate flashing on the Red ( Power ) / Amber ( User ) LED's. The static/fuzz is displayed but I'm unable to get the OSD menu. You can see here: qmLp9U.gif My setup is as follows: I'm powering my DE10 with a USB cable ( https://www.amazon.co.uk/gp/product/B003M...