MiSTer FPGA Forum

Malor wrote: ↑Wed Aug 31, 2022 5:07 pm FWIW, my DE-10 is from January, and has been flawless with Mr. Fusion.

I'm curious, can you tell me your board version number that you got in January?
Mine is 10-01610140-C1.

For running the DE-10 alone, the stock supply is fine.... if it's working correctly. The way your board is being weird reminds me a little of flaky power problems. If you were planning to get a replacement supply anyway, doing it now might help you troubleshoot. If you weren't, I wouldn't spend the money yet. I need to decide on an I/O board to ge...

LamerDeluxe wrote: ↑Wed Aug 31, 2022 7:30 pm No, I meant at the repositories where the releases come from that have the u-boot image that doesn't work for you. Maybe they could figure out the difference between your image and theirs.

Done: https://github.com/MiSTer-devel/SD-Inst ... /issues/14

i'm glad you've managed to get it sorted. Thanks for your help! This is really odd. I wonder what the difference is between the package version and your version. Have you opened a ticket about this yet? Since my board is brand spanking new direct from the manufacturer, I'm curious to see if any more people with booting issues pop up, or if my boar...

So I've built my own uboot image: https://github.com/MiSTer-devel/Main_Mi ... for-MiSTer
I flashed it directly from my pc to the sdcard with dd.
Now I have 100% boot rate success (10/10).
Something must be wonky with the uboot image in the release packages, surely?

Basically it looks like U-Boot is dying in the middle of booting, I'll probably have to build my own U-Boot image with extra debugging and use that. If anyone can point me in the direction of how MiSTer builds its U-Boot image, it'd be greatly appreciated.

I hooked up the UART cable and opened a putty session to the com port, here's what got sent on a bad boot: U-Boot SPL 2017.03+ (Oct 18 2021 - 19:11:36) Trying to boot from MMC1 U-Boot 2017.03+ (Oct 18 2021 - 19:11:36 +0800) Watchdog enabled DRAM: 1 GiB socfpga_bridges_reset: FPGA not ready, aborting. MMC: dwmmc0@ff704000: 0 And from a good boot: U-...

Yeah I've been trying that for the past hour, I think the "MiSTer SD Card Utility" utility appears to be working, it puts two partitions on the sd card and windows doesn't throw a hissy fit about it, yet. But I can't seem to boot the sd card with the nano. I've been following the manual installation method here: https://github.com/MiSTer-...

No it's just touching the glass table, it was a weird setup to film it. I have been mostly using the sd card that came with the nano, I'll swap to my sandisk and see if that helps.

Here's a 90 second video of me just turning it off and on repeatedly until it just magically works: https://youtu.be/ohqT8gH1iFk I really feel like I should be taking this up with Terasic, but since it works fine like 95% of the time with a fresh sd card, I don't know. Any suggestions? Better yet, is there any way to debug the boot sequence? I assu...

I really have no idea what's going on with this thing, the DE 10 board appears to be flaky as hell. Without touching anything, sometimes it boots, sometimes it doesn't. I was starting to think that if I wasn't making a super clean connection with the power cable when plugging it in that it wouldn't boot properly, but now I'm unsure. But I cannot ex...

Well that's an improvement! I got the second boot, I'm unsure what exactly helped, but I did a bunch of things: flipped all the switches back and forth pushed all the push buttons I also ssh'd in and ran a "sync" after the initial Mr Fusion setup I waited a lot longer after the setup before pulling the power cable I waited a lot longer be...

Thanks for the advice. I'd been using two micro sd cards so far: the 8GB "Team" sd card that came with the nano, and a 32GB Sandisk I had lying around. I had already tested them both with f3probe and they both had no issues, so I tested them both with h2testw and again both worked fine. I haven't touched the switches since the board arriv...

Hi all. I ordered my DE 10 straight from Terasic, and ordered some parts from misterfpga.co.uk, but am having issues getting up and running. I've reduced my setup back to only the DE 10, no sdram, no additional boards, only HDMI plugged in. I flash my sdcard in linux with Mr Fusion 2.5 using dd. I boot the DE 10 and get the Mr Fusion splash screen,...